![]() ![]() Remember to replace the carafe and open the Drip Stop when you're done. If you want to pour a cup of coffee before the brew is complete you can close the Drip Stop and remove your carafe to pour a cup. After adding the water and coffee, choose a size and brew type. Then insert a #4 paper filter or the permanent filter in the brew basket, and add your favorite coffee using the Ninja Coffee Scoop. #Simple delay brew coffee maker fullQ: How do I set up for single cup, travel, half carafe, full carafe, and Drip Stop? A: To brew a half carafe or full carafe, place your carafe below the brew basket and fill the water reservoir with water. Q: How do I set the clock? A: To set the clock, simply press the H button for hours and the M button for minutes until your desired time appears. This is normal since the water is automatically metered based on your brew selection. Q: Why is there water left in the reservoir? A: There may be water left in the reservoir after a brew. To reinsert, align the brew basket with the tracks on the brewer and insert at a downward angle. Q: How do I remove or insert the brew basket? A: The brew basket can be removed from the brewer by lifting the brew basket at a slight upward angle (similar to a cabinet drawer). Tip: When first setting up your Ninja Coffee Bar, we suggest running two clean cycles of just water to prime the machine. If the problem persists, call customer service at 1-87. Make sure the water reservoir is locked in place and check the Clean indicator light-if it's illuminated, run a clean cycle with the appropriate descaling solution or a white vinegar mixture.If the Ninja Coffee Bar beeps during a brew or too early: There may not be enough water in the water reservoir to complete the brew.This is to let you know it's time to replace the carafe or vessel in order to complete the brew. If you close the Drip Stop to stop the flow of coffee, to pour an early cup, or for any other reason before the brew is complete, the Ninja Coffee Bar will begin to beep after about 20 seconds.If the Ninja Coffee Bar beeps after a brew, it is signaling the brew is complete.Reopen the Drip Stop or reinsert the brew basket into the Ninja Coffee Bar. After 20 seconds, the Delay Brew will be automatically canceled. If a Delay Brew has been set and you engage the Drip Stop or the brew basket is not inserted all the way, the Ninja Coffee Bar will begin and continue beeping until closed.Check if the brew basket is inserted all the way and make sure the Drip Stop is open. If the Drip Stop is closed OR the brew basket is not inserted all the way into the brewer and you press Delay Brew, the Ninja Coffee Bar will beep for a few seconds.If the Drip Stop is closed OR the brew basket is not inserted all the way into the brewer and you press a brew button, the Ninja Coffee Bar will begin beeping. Q: Why is my Ninja Coffee Bar beeping? A:There are multiple reasons why your Ninja Coffee Bar brewer may be beeping. This process is used to evenly saturate your coffee grounds. NOTE: The brew will begin, stop, and be quiet for a short period of time before it begins again. If you hear five beeps, check that the Drip Stop is in the open position. Also, if the Drip Stop is in the open position, the brew basket may need to be pushed all the way into the brewer. A: Did you check to make sure the brewer is plugged in and water is in the water reservoir? Sounds obvious, but anything is possible if you haven't had your first cup. The clock and brew size selection remain illuminated. So after the brew is complete and the warming plate turns off, the brewer goes into standby. In fact, the Ninja Coffee Bar doesn't have an off button. Q: Is it normal for the lights to stay on for brew selection and vessel size? A: Sure is. After your brew is complete and the warming plate turns off, the Ninja Coffee Bar brewer goes into standby. Q: Where is the on/off button? A: Trick question–there isn't one. But if you want to turn it off sooner, you can-just press the Stay Warm button. After that, the warming plate will turn off automatically. Q: How long does the Precise Temp Warming Plate keep coffee hot? A: The Precise Temp Warming Plate is designed to keep your coffee hot for two hours. The light will turn off when the warming plate cools off. This may stay on for a few minutes after turning the Precise Temp Warming Plate off because the surface is still hot. The Hot Surface indicator is a safety feature to warn you the surface is currently hot. A: Just looking out for you (and your fingers). ![]() Q: I turned the warming plate off by pressing the Stay Warm button, but the Hot Surface light is still on. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |